January 24 Through February 4—TUCSON, ARIZONA: Annual show
Welcome to the GemologyOnline.com Forum
A non-profit Forum for the exchange of gemological ideas
It is currently Thu Mar 28, 2024 5:00 pm

All times are UTC - 4 hours




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Drilling turquoise.
PostPosted: Wed Sep 30, 2015 3:29 pm 
Offline
New to the Forum or The Quiet Type

Joined: Mon Sep 28, 2015 6:23 pm
Posts: 1
I am trying to work with turquoise. Knowing how soft it is any suggestions on how to drill small pieces without them crumbling. So far I had no success. What am I doing wrong. This is my first time working with turquoise. Thank you.


Top
 Profile  
Reply with quote  
 Post subject: Re: Drilling turquoise.
PostPosted: Wed Sep 30, 2015 10:47 pm 
Offline
Valued Contributor
User avatar

Joined: Wed Nov 01, 2006 5:00 pm
Posts: 391
Location: Dolan Springs, Arizona
I am drilling turquoise nearly every day. I use diamond drills that have the spiral shaft, not the solid core. I use a water troff so that my stone is underwater during drilling and I use a wood back support so that I don't have blowouts on the back side. Finally if I have any doubts about the material I back the stone with a layer of JB Weld.

What kind of turquoise are you drilling and how thick is the material?
Crumbly turquoise could be just crummy turquoise ( ie chalk).


Top
 Profile  
Reply with quote  
 Post subject: Re: Drilling turquoise.
PostPosted: Fri Dec 11, 2015 6:03 am 
Offline
New to the Forum or The Quiet Type

Joined: Sat Oct 17, 2015 6:30 am
Posts: 3
TBH any diamond drill will do ,the spirals are more for show small cos that is what people think drills should look like ( metal working). Using drills under water is good but limited due to cavitation effect and plating failing .Diamond sintered core drill will be better with water chuck, more expensive but saves money in the long run.


Top
 Profile  
Reply with quote  
 Post subject: Re: Drilling turquoise.
PostPosted: Fri Dec 11, 2015 5:32 pm 
Offline
Gold Member
User avatar

Joined: Wed Nov 15, 2006 9:44 pm
Posts: 1079
Location: Washington State
Since drilling stones is more of a grinding process than anything I've always just used ball shaped diamond bits, marked both sides and ground from both sides to the center with smaller than needed bits. Once I'm through, I clean, straighten and enlarge the hole with a diamond coated shaft like bit. Grinding from both sides just about eliminates the problem of breakout. This only works with thinner materials, like maybe 5mm maximum.

_________________
Michael E.


Top
 Profile  
Reply with quote  
 Post subject: Re: Drilling turquoise.
PostPosted: Sat Dec 12, 2015 12:33 pm 
Offline
Gemology Online Veteran

Joined: Sat Apr 24, 2010 7:10 am
Posts: 584
Like drilling holes in anything else you need the turquoise to be rigidly held and the drill to approach from one angle and stay on course through the stone......any material that moves around when drilling will make a sloppy hole or get thrown and have a chance of being damaged or doing damage. The type of drill won't matter


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 4 hours


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Gemology Style ported to phpBB3 by Christian Bullock